Lennox Furnace Repair Nationwide

Lennox Furnace Repair in Houston: What to Know First

Lennox furnace repair in Houston typically runs between $150 and $700, and most jobs are completed in a single visit since our trucks carry common Lennox OEM components. We’re an independent Lennox service provider, which means we repair these furnaces without being tied to manufacturer pricing or scheduling, and you get a written price before any work starts. If your Lennox furnace is short cycling, throwing an error code, or blowing cold air on a damp Houston night, call (346) 201-5395 and a live person will answer, day or night.

Call (346) 201-5395

This page is for Houston homeowners with a Lennox furnace, whether it’s a Merit series in a 1990s ranch house near Garden Oaks, an Elite in a two-story near Clear Lake, or a newer Dave Lennox Signature unit out toward Katy. We’ll walk through how these specific furnaces fail in our climate, what repairs actually cost, and how our crew handles a Lennox job from the first call to the final shoe-cover check at your front door.

How Lennox Products Fail – and How We Fix Them

• Merit Series ML193 pressure switch trips during humid cold fronts. Houston’s winter air swings between damp and dry faster than most furnaces were designed to handle. The ML193’s pressure switch senses flue draft, and when a cold front dumps moisture into the venting, the switch can flutter open mid-cycle. We see this most often in older homes near Braeswood Place where flue pipes run through uninsulated attics. Our fix is checking vent slope and condensate drainage before condemning the switch itself, which saves Houston families from paying for a part they didn’t need.
• Elite Series EL296V variable-speed blower motor failure from dust and pet hair. The EL296V is a great furnace, but its ECM blower motor pulls air through the return at a higher static pressure than single-speed units. In homes with golden retrievers and cats, that means hair and dust collect on the blower wheel faster, which strains the motor module. When we open one of these up in a house near Cypress, we often find a blower wheel that looks like it’s wearing a fur coat. We clean the wheel, test the module, and only replace the motor if the bearings or electronics have actually failed. That diagnostic step alone has saved customers hundreds.
• Dave Lennox Signature SLP98V ignitor cracks from attic heat cycling. The SLP98V uses a silicon nitride ignitor, which is more durable than the old carbide style, but Houston attics push past 140°F in August. A furnace installed in a hot attic goes through wild temperature swings, and ignitors are ceramic. They crack. The symptom is usually an error code that points at ignition lockout, and the unit will try three times then shut down. We keep OEM silicon nitride ignitors for the SLP98V on the truck, and we check the burner alignment while we’re in there, because a misaligned burner can short the ignitor’s life.
• EL195E heat exchanger hot spots from dirty evaporator coils. Many Houston homeowners run their AC for eight months of the year and never think about the coil sitting above the furnace. A neglected evaporator coil restricts airflow into the furnace, and restricted airflow over a Lennox heat exchanger means it runs hotter than designed. Over years, that creates hot spots and eventually cracks. We always inspect the coil when a Lennox furnace shows signs of overheating, and we’ll show you photos of what we find. A cracked heat exchanger on an EL195E isn’t something to gamble with, so we shut the unit down and give you honest repair-vs-replace numbers the same day.
• Merit ML180 gas valve sticking after long idle seasons. Houston furnaces sit idle from March to November, and gas valves don’t love sitting still. The ML180’s valve can stick closed on the first cold snap of the year, which sounds like the furnace clicking but never lighting. We test gas pressure at the valve inlet and outlet, because sometimes the issue is actually a regulator at the meter or a spider web inside the burner orifice, which happens more often than you’d think in quiet Houston attics. If the valve is truly stuck, we replace it with an OEM Lennox valve, not an aftermarket one, because the ML180’s manifold pressure settings are tighter than universal valves handle well.

Our Lennox Furnace Repair Process

1. 1
   You call, a person answers. No phone tree, no voicemail at 2 a.m. We ask what the furnace is doing, what the thermostat says, and whether you’ve noticed any smells or sounds. Luis Serrano’s standing rule: “Tell me what the house is doing, and we’ll figure out what it actually needs.”
2. 2
   We show up in a stocked truck, wearing shoe covers before we step inside. Our techs carry Lennox OEM ignitors, flame sensors, pressure switches, gas valves, and blower motors for the most common series, plus drop cloths that go down before any tools do.
3. 3
   We diagnose with the furnace running. We watch the full sequence of operations, measure gas pressure, test the flame sensor, and inspect the heat exchanger if the unit’s age or symptoms call for it. You get a written price before any repair begins, and that price doesn’t change unless we find something genuinely dangerous hiding behind the original problem, in which case we stop and show you photos.
4. 4
   Parts decision: OEM when it matters, quality aftermarket when it doesn’t. For gas valves, ignitors, and control boards on newer Lennox units still under warranty, we use OEM parts. For things like universal pressure switches or capacitors on out-of-warranty furnaces, we’ll offer a quality aftermarket option and tell you the honest trade-off in lifespan and cost.
5. 5
   The repair is tested, not just finished. We cycle the furnace through at least five complete heat cycles after the repair, check temperature rise across the heat exchanger, and confirm the error codes are gone. We don’t consider a job done until the furnace lights on its own, reaches set point, and shuts off cleanly.
6. 6
   Cleanup, photos, and the 365-Day Done Right Promise. We vacuum around the furnace, put back anything we moved, and take a photo of the clean work area before we walk out. You get a copy of that photo, the written invoice, and the guarantee: if it’s not done right, we make it right. No runarounds, no fine print.

What Lennox Furnace Repair Costs in Houston

Most Lennox furnace repairs in Houston fall between $150 and $700, depending on what failed and which series you own. Here’s a realistic breakdown of what Houston families typically pay:

• Flame sensor cleaning or replacement: $150 – $250
• Ignitor replacement: $200 – $375
• Pressure switch replacement: $180 – $320
• Gas valve replacement: $350 – $600
• Blower motor replacement: $400 – $700
• Draft inducer motor replacement: $300 – $550
• Heat exchanger inspection: included with diagnostic when the unit’s age or symptoms warrant it

What moves the price is parts cost (high-efficiency Dave Lennox Signature units carry pricier components than Merit series furnaces), the age of the unit, and whether the repair requires accessing a furnace in a tight Houston attic versus a closet in a first-floor hallway. Every quote is written before work starts, and the diagnostic fee is applied toward the repair when you move forward with us. Call (346) 201-5395 and we’ll give you a straight price before anyone touches a tool.

Why Houston Homeowners Call Meadowsweet Heating and Air Houston for Lennox Work

Three things set us apart, and they’re all things a homeowner can feel. First, the Cedarwell Care Promise: a written price before any work starts, background-checked uniformed technicians, and a 365-Day Done Right Promise that backs every single job. If a repair doesn’t hold, we come back. Second, our crew follows the C.A.R.E. values code on every visit: Clean up like it’s their own home, Ask before moving anything, Respect the family’s time and quiet hours, Explain the price before the work. We put down shoe covers and drop cloths so your floors, playroom carpet, and the air your kids and pets breathe stay clean while we work. Third, we’re not a one-brand shop. We also service Carrier and Trane, which means when a Lennox repair isn’t the right call, we’ll tell you with an informed perspective rather than a sales pitch. Luis Serrano and his team have served Houston neighborhoods from the Energy Corridor to Clear Lake, and the standard is the same everywhere: leave the home as clean as we found it, with the furnace working right.

FAQs